CL2200 Electronic Surface Deadbolt

Tools required for installation

• Power drill
• 25mm (1"), 13mm (1/2") & 8mm (5/16") drill bits
• Bradawl
• Philips screwdriver size 2
• Chisel - maximum 25mm (1")
• Hammer / Mallet
• Stanley knife
• Adhesive tape
• Pencil
• Tape measure

Special Notes You are advised to familiarise yourself with the instructions before starting work. 1. Install the 2 x AA cells supplied into front plate. 2. A BLEEP should be heard when you do this. If no BLEEP is heard then check that the batteries are correctly installed. 3. Enter the factory Master Code, 1234 (note: when programming the badge bar must prefix the Master Code). The blue light will flash and thefront knob will be able to be turned using finger and thumb. 4. After installation change factory set Master and User Codes - see programming instructions provided.
1. Check the hand of your door Your door is right-handed if vierwed from outside, the hinges are on the right.
2. Positioning the lock 1. Remove the inside cover plate from the back plate, and install the deadbolt according to the hand of your door. Note that the standard bolt projects 40mm (9/16") to the locking side. A shorter bolt which projects 20mm (3/4") is available. 2. Set the back plate with the knob in the vertical position and hold it to the door with one end of the bolt against the frame where the keeper will be fitted (see step 4). 3. Mark the position of the top fixing hole, and then using one of the packing pieces as a template make the position of the lower fixing hole and the hole for the spindle. Drill 8mm (5/16") holes for fixing bolts and 13mm (1/2") hole for spindle.	Note: Establish which keeper to use, and mark its position on the frame, before proceeding to drill the door for the lock (see step 4).
3. Fixing the lock 1. Cut the fixing bolts to suite the door thickness, length of bolts measured beneath the bolt head should be door thickness plus 15mm (5/8"). 2. Using the inside knob check that the spindle moves freely, and that the latch retracts and projects smoothly. If it is tight, loosen the fixing bolts slightly and adjust the position of the back plate until the spindle will turn freely. Tighten the fixing bolts. Test the spindle again. DO NOT over-tighten the bolts as this may cause the door to distort and affect the lock function. DO NOT CLOSE THE DOOR UNTIL YOU ARE SURE THAT THE CODE WORKS	Note: Do not close the door until you are SURE that the code works.
4. Fitting the keeper 1. First select the appropriate keeper for your frame. 2. Position the keeper on the frame so that it lines up with the deadbolt and makr the appropriate holes. 3. If you are using the Surface Keeper simply screw into place (see fig. 5.1). Use the packing peices as required. 4. The Mortise Keeper will require cutting a small recess (see fig 5.2).	Surface Keeper fig 5.1   Mortise Keeper fig 5.2

* Instructions for CL2255 and CL2200 models

CODES
• The factory set Master Code is #1234. This should be changed immediately after installation (see program 10).
• The Master Code and optional Sub-Master Code always start with the # prefix. This puts the lock into Programming Mode.
• When the Master or Sub-Master Code is entered 3 times consecutively without performing a programming function, a penalty time of 10 seconds is activated. This feature is to discourage the casual use of Master Codes as User Codes.
• The length of the Master Code determines the length of the User Code and the Sub-Master Code.
• If the Master Codes is changed to another of the same length then the Sub-Master and all User Codes will be retained.
• If the Master Code is change to one of a different length then the Sub-Master and User Codes will be deleted.
• Codes may be 4, 5 or 6 digits long.
• The lock memory will store 80 different User Codes, each identified by a User Code ID – 01 to 80.
• The lock memory can store 10 different One Time User Codes. Each One Time User Code is identified by a One Time User Code ID – 81 to 90.
• When in Programming Mode a Program Code must be entered within 5 seconds, otherwise the Red light will flash and beep and the lock will revert to normal.
• If a programming mistake is made wait 5 seconds, the Red light will flash and beep and the lock will revert to normal.
• A new code will be rejected if it is already in the memory.

OPERATING INSTRUCTIONS
The CL2000 locks have an 11 button keypad including the Badge Bar which acts as the # button.

UNLOCK TIME
The factory pre-set UNLOCK time is 4 seconds. This may be changed – (see Program 06).

PENALTY TIME
Entering 3 incorrect User codes will cause the lock to suspend activity for a penalty time of 10 seconds.

KEY OVER-RIDE
Turning the key clockwise with retract the latch allowing the door to be opened.

CODE FREE MODE
Using the Master or the Sub-Master Code, programs 08 and 09 will put the lock into, and out of, Code Free Mode. In Code Free Mode battery power is not being used.


REVERTING TO FACTORY SETTING

If the Master Code is not known the lock memory can be cleared and made to revert to the factory Master Code as follows:

1. Remove one battery.
2. Press and hold the ‘0’ button, replace the battery, the Blue LED will flash twice, beep will sound twice, then release the ‘0’ button.
3. Within 3 seconds press the ‘0’ button 3 times. The Blue LED will light continuously for 7 seconds and then 2 beeps will sound. The lock will have reverted to the factory set Master Code, #1234, and all other settings will be erased.

REMOTE RELEASE OPTION
The lock has 2 sets of terminals for remote release, labelled REM 1 and REM 2 on the printed circuit board in the front housing. Cables are provided with the lock for these connections



REM 1 is intended for use when there is a need to allow a visitor to open the door after having been identified by intercom or by sight from within. REM 1 would be connected to a pushbutton on a reception desk, or to the appropriate button on an intercom. Pushing the button would cause the Blue LED to light and would release the lock for the normal set time.

REM 2 is intended for use when there is a need for the door to be release by an alarm system, such as a fire alarm. This enables emergency personnel to rapidly check that no one is trapped / overlooked in classrooms, wards, guest rooms, etc during a fire drill. When activated by an alarm REM 2 will maintain the unlocked condition for 30 minutes. During this time the red LED will flash once every second and beep to indicate the unlocked condition.  The lock will automatically revert to normal after 30 minutes. If required Program 11 can be used to revert the lock to normal before the 30 minute period has finished.

LOCKED / UNLOCKED STATUS INDICATION
Using Program 15 the Blue and Red LED’s can be programmed to indicate locked and unlocked status.

BATTERY POWER
These Electronic Codelocks should provide well in excess of 200,000 openings from 4 x AA cells rated at 2,900 mAh.

LOW BATTERY
When the battery power is low the Red LED will flash 5 times before the Blue LED will flash 5 times before the Blue LED flashes to signal acceptance of the code. Batteries should be changed as soon as this happens.

BATTERY FAILURE OVERRIDE
The CL2000 series has been designed so that a PP3 battery can be used to open the lock should batteries fail. See image below.
The procedure is as follows:
• Place the terminals of the PP3 battery against the contact points on the lock.
• The positive + PP3 terminal to the left hand contact.
• The negative –PP3 terminal to the right hand contact.
• On secure maintained contact the lock will beep twice and the blue light will flash twice.
• On secure maintained contact the lock will beep twice and the blue light will flash twice.
• Maintaining contact enter the Master Code.
• The clutch will release allowing to the lock to be opened.
• Fit the new batteries to the lock by remove the battery cover on the inside of the door.

PROGRAMMING

* First change the factory Master Code – see program 10. If the Master or Sub-Master Code is entered 3 times consecutively without performing a programming function, a penalty time of 10 seconds is activated.
Note: The Badge Bar at the bottom of the keypad acts as the # button.
The Master Code and Sub-Master Code MUST always start with #.
Codes can only be the same length as the Master Code.
A • or • in the Key Sequence below indicates LED illumination.

If entered, a Sub-Master Code can be used instead of the Master Code for all programs except program 10 and 12.

ENTER NEW USER CODE   Program 01
Key Sequence
#Master Code • 01 • User Code ID (eg 05), New Code (eg 4321) ••
Result
New Code 4321 entered at User Code ID 05
(• when user enters code)

SUPEND USER CODE   Program 02
Key Sequence
#Master Code • 02 • User Code ID (EG 05) ••
Result
User Code at ID 05 suspended
(•• when user 05 enters code)

RESTORE USER CODE   Program 03
Key Sequence
#Master Code • 03 • User Code ID (eg 05) ••
Result
User Code at ID 05 restored
(• when user 05 enters code)

SUSPEND ALL USER CODES   Program 04
Key Sequence
#Master Code • 04 ••
Result
All User Codes suspended
(•• when all users enter code)

RESTORE ALL USER CODES   Program 05
Key Sequence
#Master Code • 05 ••
RESULT
All User Code restored
(• when all users enter code)

CHANGE UNLOCK TIME   Program 06
Key Sequence
#Master Code • 06 • enter open time
(range 2 – 9 secs) ••
RESULT
After code entry the lock will unlock for the set time
(Factory pre-set time is 4 seconds)

ONE TIME USER CODES   Program 07
Key Sequence
#Master Code • 07 • One time code ID
(eg 81) • One time Code (eg 4321) ••
RESULT
Code 4321 in position 81 will work once and then be removed from memory
Note: ID Positions 81 to 90 are reserved for this program functions, allowing up to 10 One-Time User Codes to be entered.

SET CODE FREE MODE   Program 08
Key Sequence
#Master Code • 08 ••
RESULT
Lock will be continuously unlocked

CANCEL CODE FREE MODE   Program 09
Key Sequence
#Master Code • 09 ••
RESULT
Lock will revert to normal operation

CHANGE MASTER CODE   Program 10
Key Sequence
#Master Code • 10 • enter length of Master Code
Followed by new Master Code (eg 6, 123456) •
Confirm length of Master Code followed by new Master Code (eg 6, 123456) ••
RESULT
Master Code now changed to #123456. Note: If the length of the Master Code is changed then all previous User Codes will be deleted

CANCEL EMERGENCY OPEN MODE   Program 11
Key Sequence
#Master Code • 11 ••
RESULT
The emergency unlocked condition via REN 2 will be cancelled and the lock will revert to normal operation




DELETE ALL USER CODES   Program 12
Key Sequence
#Master Code • 12 • 12 •• (7 secs)
RESULT
All User Codes will be cleared from the memory

ADD/CHANGE SUB-MASTER CODE   Program 13
Key Sequence
#Master Code • 13 • Sub-Master Code (eg 2468) ••
RESULT
A Sub-Master Code #2468 has been entered

DELETE SUB-MASTER CODE   Program 14
Key Sequence
#Master Code • 14 • 14 ••
RESULT
Sub-Master Code has been deleted

LOCKED/UNLOCKED STATUS   Program 15
Key Sequence
1. #Master Code • 15 • 1 •• = Locked, No LED flashing (this is the default setting)
2. #Master Code • 15 • 2 •• = Locked – Red • LED flashing
3. #Master Code • 15 • 3 •• = Unlocked – Blue • LED flashing
RESULT
If activated LED’s will flash continuously every 5 seconds
Note: LED’s will not indicate unlocked mode by key