CL210 Installation Guide

Number relating to picture	Item	CL210
1	Front plate	*
2	Back plate	*
3	Neoprene seals x 2	*
4	Spring loaded spindle	*
5	Deadbolt 2 3/8" and 2 3/4" (inches) backset	*
6	Keeper plate	*
7	Wood screws x 4 - Use with the deadbolt and keeper plate	*
8	Deadbolt support post	*
9	Tweezers	*
10	Fixing bolts x 3 (1 x spare)	*
11	Spare code tumblers x 2	*
12	Code card	*

Special Notes
You are advised to familiarise yourself with the instructions before installing.

Before commencing installation check that all parts are working correctly -press the code according to the code card and the knob should then turn, in either direction, once only, and return easily under spring pressure.
If you intend to change the code, you should do it, if it is convenient before installing the lock - see the code change instructions.
Check that the deadbolt moves freely by turning the flat spindle in the cam.
From outside the code is required both to lock and to unlock the bolt. If you would like to be able to lock your door from outside without using the code then follow instruction 1.

If you would like to lock the door without entering the code, follow these instructions:

NB Your door is right handed if, from the outside, the hinges are on the right. To enable locking of the bolt from outside without using the code:

Press the ‘C’ button to reset the chamber and place the lock case on a flat surface with the buttons down.
Remove the code chamber plate held in place with the two red screws.
With the tweezers remove the right hand pin for right handed doors, or the left hand pin for left handed doors.
Replace the cover plate
The outside knob will now feel loose and turn freely in one direction, and will require the code to be used before it will turn in the other direction.

Codelocks CL200 Mechanical Lock Diagram

Please Note: When installing the lock make sure that the driver is in the correct position before installing the spindle.

Crease the template along the door edge line and tape it to the door.
Mark the 5/8" (inches) holes, and the 2 3/8" (inches) holes. Mark the centre of the door edge on the centre line of deadbolt.
Apply the template to the other side of the door, aligning it with the first mark in the middle of the door edge, and mark the 5/8" (inches) holes and the 2 3/8" (inches) holes again.
Keeping the drill level and square to the door, drill the holes from both sides to avoid splintering out the door face.
Use a chisel to clear the 2 3/8" (inches) holes into a single square hole.

Positioning and fixing the deadbolt

Drill a 1" (inches) hole, 3 7/8" (inches) deep, on the mark on the centre of the door edge. Be careful to keep the drill level and square to the door.
Put the deadbolt into the hole and draw around the faceplate.
Remove the deadbolt. Score the outline with a Stanley knife prior to chiselling a 1/8" (inches) deep rebate to accept the faceplate flush to the door.
Fix the deadbolt with the wood screws.

Fit the deadbolt support post in hole A for a right hand hung door, or B for a left hand hung door. Your door is right handed if, viewed from outside, the hinges are on the right.

The spring loaded spindle (pat app) will fit doors between 1 3/8" and 2 5/8" (inches) thick. For doors less than 2 1/8" (inches) remove the 5/8" (inches) break off end of the spindle. The spindle will then fit doors between 1 5/8" and 2 1/8" (inches). The spring keeps the spindle firmly engaged and prevents it moving out of engagement with either of the plates.
Insert the spindle, with the spring to the outside, through the slot in the deadbolt.
Cut the fixing bolts to suit the door thickness, allowing at least one, but no more than two, threaded sections to enter the lock case.
Hold the lock case and the back plate, with the seal, onto the door with the spindle in position.
Using the fixing bolts screw everything together, first through the top, and then through the bottom hole of the back plate. Before final tightening make sure that the lock is vertical, and test the mechanism to ensure that it is all moving easily. Do not close the door until you are sure that the code works, do not overtighten the fixing bolts as this may cause distortion and lead to poor operation.

Codelocks CL210 Lock Installation Diagram

Position the keeper plate on the frame so that it lines up with the deadbolt.
Mark the inner and outer edges of the keeper plate and cut a rebate so that it fits flush with the surface of the door frame.
Drill or cut a recess 1" (inches) deep for the deadbolt.
Fit the keeper plate using only one wood screw at first to ensure that it is positioned accurately. The deadbolt should enter the aperture easily. When satisfied secure the keeper with the second screw.

Surface Keeper Fig 5.1

Mortice Keeper Fig 5.2